CPlane

Toolbar Menu

CPlanes
Standard

View

Viewport context menu

Set CPlane

The CPlane command sets the origin and orientation of the construction plane in the active viewport.

A construction plane is like a tabletop that the cursor normally moves on. The construction plane has an origin, x and y axes, and a grid. The construction plane can be set to any orientation, and each viewport’s construction plane is independent of those in other viewports.

The construction plane represents the local coordinate system for the viewport and can be different from the world coordinate system.

Rhino’s standard viewports come with construction planes that correspond to the viewport. The default Perspective viewport, however, uses the world Top construction plane, which is the same construction plane that is used in the Top viewport.

Steps

Command-line options

All

The construction planes in all viewports change so their origin is at the picked location.

Curve

The Curve option sets the construction plane perpendicular to a curve.

Curve steps

  1. Select a curve to orient construction plane.
  2. Drag the construction plane's new x and y axes to a new location.

Note

  • Use the Curve option to quickly position your construction plane at various stations along a central rail curve as preparation for doing a one rail sweep, for example. Once your construction plane is positioned, you can use drawing tools to draw a cross-section curve in the 3 D location where it needs to be. This direct drawing method can be quicker and more convenient than drawing the curve on a world plane and then trying to move and rotate it into place in 3‑D.
  • The direction of the curve affects the direction of the axes. If the construction plane does not go the direction you want, flip the direction of the curve with the Flip or Dir commands.

SubCrv

Type subcrv to select part of a curve as input.

Elevation

The Elevation option changes the elevation (z direction) of the construction plane.

Elevation steps

  • Pick a new elevation.
    Or
    Type a distance to move the origin from its previous location.

Note

  • Positive numbers move the construction plane up along the positive z axis.
  • Negative numbers move the construction plane down.

Object

The Object option sets the construction plane in the active viewport to an object.

Object steps

  • Select a curve or surface.
    The origin and tangency of the new construction plane is based on the "midpoint" of the untrimmed version of the surface.

Rotate

The Rotate option rotates the construction plane.

Rotate steps

  1. Pick the start of the rotation axis.
  2. Pick the end of the rotation axis.
  3. Type the angle to rotate the construction plane.
    Or
  4. Pick two points to specify the angle.

Surface

The Surface option sets the construction plane to match a surface. The placement is constrained so that the construction plane is tangent to the surface.

Surface steps

  1. Select a surface.
  2. Pick an origin or press Enter.
  3. Pick an x axis direction or press Enter.

Surface options

Flip

Reverses the direction.

IgnoreTrims

Uses entire untrimmed underlying surface.

Through

Moves the construction plane origin to a selected point.

Through steps

  • Pick a location to move the origin to.

Through option

All

Resets all construction planes to the new origin.

View

Sets the construction plane in the active viewport parallel to the view.

View steps

  • Click View or type V.

World

Restores the specified default construction plane.

World steps

Back
Bottom
Front
Left
Right
Top

3Point

The 3Point option sets the construction plane in the active viewport by specifying points to establish the x, y, and z directions.

3Point steps

  1. Pick a new origin, or press Enter.
  2. Pick the x axis.
  3. Pick the y axis.

3Point options

Vertical

Sets the construction plane perpendicular to the current construction plane.

ZAxis

Sets the construction plane z axis direction.

Undo

Restores the previously used construction plane in the current viewport.

Undo steps

  • Click Undo or type U.
Shortcut

Shift + Home

Redo

Restores the construction plane that was active before the Undo option was used.

Redo steps

  • Click Redo or type D.
Shortcut

Shift + End

CopyCPlaneToAll

Toolbar Menu

Not on toolbars.

Not on menus.

The CopyCPlaneToAll command changes all viewports to have the same construction planes as the specified viewport.

CopyCPlaneSettingsToAll

Toolbar Menu

Not on toolbars.

Not on menus.

The CopyCPlaneSettingsToAll command changes all viewports to have the same grid settings and snap spacing as the specified viewport.

See also

MPlane

Set up a relationship between a construction plane and an object.

NamedCPlane

Manage the named construction planes list.

Use construction planes

 

 

 

Rhino for Mac © 2010-2017 Robert McNeel & Associates. 24-Oct-2017